Top 10 typical forklift mishaps ， forklift procedure must focus on these matters ！.

Top 10 typical forklift mishaps ， forklift procedure must focus on these matters ！.

Blog Article

Do not ignore the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the motorist's view, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these matters ：.

Beginning.
1. Prior to starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe prior to starting.
3. When the forklift begins with a tons, the driver needs to first verify that the tons is steady and dependable.
4. The start needs to be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be slanted in reverse. .
2. Do not raise the fork too high when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges in the sky. When the lots is traveling, the fork should not be raised expensive, which will influence the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving setting prior to driving. .
4. When turning, if there are pedestrians or vehicles close by, the driving signal needs to be released initially. High-speed doglegs are prohibited. High-speed sharp turns will cause the car to shed side stability and topple. .
5. When the forklift is downhill, it is strictly forbidden to turn off the fire and slide, and it is forbidden to brake instantly while driving with loads unless there are special circumstances.
6. When the forklift is running, it needs to comply with the traffic rules in the factory and need to maintain a particular safety and security range from the lorry in front. .
7. When the forklift is running, the tons must remain in the most affordable setting that does not prevent the driving, and the gantry must be effectively slanted back. The lots shall not be increased except when piling or filling. .
8. The elevation of the tons need to not obstruct the chauffeur's sight. In special circumstances, when the product influences the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive securely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, lifted or driven, Stand-on Electric Pallet Stacker it is prohibited for personnel to depend on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely way, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between the two forks ought to be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the product should be against the shelf. .
2. It is prohibited to collaborate with a single fork or make use of a fork top or draw. In unique circumstances, safety indication should be established to advise surrounding pedestrians. .
3. In the process of loading and discharging items, the forklift has to be braked with the brake. .
4. The speed of the vehicle need to be sluggish and stable. Beware not to roll the wheels on the dunnage, so as not Stand-on Electric Pallet Stacker to extend the rolled things and hurt individuals. .
5. When making use of a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch other goods or items. The lots ought to be stabilized with marginal back tilt of the gantry so that the tons does not slide backwards. The mast can be tilted onward somewhat when the tons is decreased to enable easy placement of the load and removal of the forks. .
6. It is forbidden to fork goods at broadband and collide with difficult things with the fork head. .
7. When the forklift is working, it is restricted for individuals to loaf the fork, so regarding avoid the collapse of the goods and hurt individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to participate in high-altitude procedures to prevent high-altitude falling mishaps. .
9. It is not permitted to use the brake inertia to slip, place, round or roll items. .
10. It is not permitted to use forks to choose, turn pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you need to discharge the goods or lower the fork framework.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is shut off and the power is removed. (Except for unique conditions, such as the driver does not leave the car's line of sight and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look must be examined, and gas, lubricating oil and cooling water need to be included.
2. Examine the security efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak needs to likewise be examined and the seals must be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning should not be too sharp to prevent the propensity of " cost-free switching";.
6. Adding and down the incline ought to be sluggish and uniform, and no activating the slope is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel carry the goods and progress, if they come across huge or hefty products and most likely to the chauffeur's line of vision, they need to take the turning around exercise
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Solitary fork operation is not allowed.
2. It is not enabled to raise the goods for cross country driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to make use of braking pressure to exile round or easy-to-roll items.
7. It is not allowed to bring people to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the list below conditions.
1. Contours, narrow roadways, railway crossings;.
2. Areas with a longitudinal slope more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the same length as the challenge ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844